Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Dilworth?
Chimney cap and crown work in Dilworth typically runs $285 to $1,450 depending on what’s being replaced. A standard stainless cap installed over an existing flue usually lands between $285 and $520, while a full crown rebuild with proper pitch and drainage runs $750 to $1,450. If both the cap and crown need attention at the same time, expect the combined estimate to sit in the $950 to $1,750 range.
Those numbers reflect the Dilworth market in 2026, where brick chimneys on older homes in the neighborhood are the norm and many crowns have been patched once too often. The written estimate always sets the final price, and the estimate itself is free. Call (888) 378-0297 if you want a firm number. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
- Cap only (standard stainless): $285 to $520
- Custom or decorative cap: $520 to $950
- Minor crown patching (cracks under 1/4 inch): $350 to $600
- Full crown rebuild, standard masonry: $750 to $1,450
- Crown rebuild with cap replacement together: $950 to $1,750
- Multi-flue cap (two or three flues under one cap): $480 to $1,100
Key Takeaways
- Most Dilworth homeowners pay $285 to $520 for a cap and $750 to $1,450 for a crown rebuild.
- Crown damage is the most common cause of water intrusion we find on brick chimneys in this neighborhood.
- Older brick chimneys in Dilworth often have crowns that were patched with mortar instead of rebuilt with proper pitch, which is why they fail again within a few seasons.
- A written estimate is free and sets your final price.
- Our technicians have up to 12 years of experience with cap and crown work, and we document what we find before we recommend anything.
Chimney Cap & Crown Cost Breakdown (2026)
The table below shows typical estimated ranges for Dilworth. Every job is different, so treat these as starting points rather than quotes.
| Line item | Typical range | What it covers |
|---|---|---|
| Standard stainless steel cap | $285 – $520 | Single-flue cap with mesh screen, sized to your flue opening |
| Multi-flue cap | $480 – $1,100 | One cap sheltering two or three flues, common on older Dilworth homes with more than one fireplace |
| Custom or copper cap | $520 – $950 | Non-standard sizing, decorative styles, or copper construction from brands like Copperfield |
| Crown crack repair (minor) | $350 – $600 | Sealing hairline and surface cracks with a flexible masonry sealant |
| Crown rebuild | $750 – $1,450 | Removing the old crown, forming a new one with correct slope, and finishing with proper overhang |
| Cap and crown together | $950 – $1,750 | Both components replaced in one visit, which is where most water intrusion problems get solved |
| Cap replacement during a rebuild | Included in rebuild estimate | Pricing determined by the written estimate |
What pushes a job toward the higher end? Access is the biggest one. A chimney on a steep roof or a two-story home takes longer to work safely, and that time shows up in the estimate. Crown size matters too. A wide crown on a large masonry chimney uses more material than a compact one. Material choice on the cap side is a smaller factor but still real: a standard stainless cap from Gelco or Famco costs less than a custom copper piece from Copperfield. On the crown side, the condition of the brick just under the crown drives cost. If the first course of brick is spalling or loose, it has to be rebuilt before a new crown goes on, and that brickwork adds to the total.
What brings it down? Doing both at once. If the crown is coming off anyway, the cap install happens in the same visit and you avoid a second trip. Choosing a standard stainless cap over a custom one saves money without a meaningful difference in performance. And catching a hairline crack early, before water gets into the brick, keeps the job in the $350 to $600 range instead of the $750 to $1,450 rebuild range.
What Affects Chimney Cap & Crown Pricing in Dilworth
- Roof pitch and access. The neighborhood’s older houses sit on a mix of gentle and steep rooflines. A steep roof requires more setup and more care, which raises the estimate. Nothing about that is negotiable, and any outfit that skips safe access is cutting a corner you’ll pay for later.
- Crown condition under the surface. A crown that looks fine from the ground can be hollow underneath. If the bond has broken down, patching it is throwing money at a problem. That’s why we inspect first and show you what’s going on before pricing the fix.
- Number of flues. A two-flue or three-flue chimney needs a larger or custom cap. More flues, more material, higher line item. Simple as that.
- Cap material and construction. Standard stainless from Gelco or Famco sits at the lower end. Copper caps from Copperfield cost more up front because of the material. Both keep animals and water out. The difference is mainly appearance and how long the finish holds.
- Brick condition at the crown line. If the top courses of brick are loose, spalled, or missing mortar, that repair happens before a new crown goes on. It’s not padding the estimate, it’s the only way the crown stays put.
- Whether a liner is also involved. Sometimes the crown failure has let water down the flue for years, and the liner underneath is compromised. If a DuraFlex liner or HeatShield resurfacing is needed on top of the cap and crown work, the total estimate goes up. That’s why a chimney inspection before any pricing makes sense.
How to Save on Chimney Cap & Crown
Get the crown looked at before you patch it again. A lot of Dilworth homeowners have had a crown patched two or three times at $350 to $600 a pop. That adds up past the cost of a proper rebuild, and the water problem never actually stops. One rebuild done right, with correct slope and overhang, is cheaper over a handful of years than repeated patching.
Bundle the cap with the crown. If the crown is coming off, that’s the moment to install a new cap. Same visit, one setup, no second trip charge buried in a separate estimate. For a Dilworth chimney that needs both, the combined job typically runs $950 to $1,750 instead of two separate jobs priced independently.
Choose a standard stainless cap unless you have a reason for something else. A $285 to $520 stainless cap from Gelco or Famco does the job: it keeps rain, birds, and squirrels out, and it won’t need replacing for years. A copper cap from Copperfield is a fine choice if you want the look, but it’s not necessary for function.
Get the inspection first. A documented inspection tells you whether you’re looking at a $350 patch or a $1,450 rebuild. Guessing is how people overpay or underpay. We document what we find before we recommend anything, and that report tells you exactly what your money is going toward.
Ask for the written estimate before work starts. Every job we quote is priced per job, set by the written estimate, and the estimate is free. Call (888) 378-0297 and we’ll get you scheduled. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Crown and Cap Work Matter More Than Most Homeowners Realize
A clean chimney is the starting point, not the finish line. The crown is the concrete or mortar cap at the very top of the chimney, and its job is to shed water away from the brick below. When it cracks, water goes in. When water goes in, it freezes in a Dilworth cold snap, expands inside the brick, and pushes the face off. That’s spalling. Once spalling starts, you’re looking at brick repair on top of the crown repair, and the bill climbs well past the $750 to $1,450 crown range.
The cap does a different job. It keeps rain out of the flue opening and animals out of the chimney. A missing cap lets birds nest and squirrels take up residence, and a nest in a flue is a fire waiting to happen. A cap is the least expensive part of the whole system to fix and one of the most consequential to skip.
This is why the two go together. Both address water intrusion from above. Both are cheap relative to the damage they prevent. And both get overlooked by sweep-only outfits that clean the flue and leave the crown cracked. If you’ve had a sweep come through and the crown wasn’t mentioned, that’s a gap worth closing. See our chimney cap & crown page for the full scope of that service, or start with a formal inspection to see where your chimney actually stands.
What a Cap and Crown Job Looks Like
Every engagement can begin with a chimney inspection if you haven’t had one recently. We look at the crown, the cap, the flue, the liner, and the firebox, and we write down what we find. From there, the recommendation follows the findings, not the other way around.
If the crown only has surface cracks, we clean them out and seal them with a flexible masonry sealant that moves with the chimney instead of cracking away from it. If the crown has lost its bond, it comes off. We form a new crown with the correct slope so water runs off instead of pooling, and we give it proper overhang past the brick face so runoff doesn’t travel down the wall. Then the cap goes on, sized to the flue opening, screwed down, screened on the sides.
We source caps and venting components from Gelco, Famco, and Olympia Chimney, brands specified by certified chimney professionals. If a liner turns out to be compromised while we’re up there, we can address that too, either with a DuraFlex flexible liner system or with HeatShield ceramic resurfacing depending on the condition. One company handles the diagnosis through the completed repair, which means no handoffs and no gaps in accountability.
One safety note: chimney work at height is genuinely dangerous, and crown material is heavy. If you’re thinking about getting up there yourself, don’t. A slip on a roof or a dropped crown section is not worth the money you’d save. Trained technicians handle this, and the local pros we connect you with are licensed and insured as their state requires.
FAQs – Chimney Cap & Crown Cost
How much does a chimney cap cost in Dilworth?
A standard stainless steel chimney cap in Dilworth typically costs $285 to $520 installed. Custom or copper caps run $520 to $950, and multi-flue caps for chimneys with two or three flues fall between $480 and $1,100. Call (888) 378-0297 for an exact quote. Estimates are free.
How much does a chimney crown rebuild cost in Dilworth?
A full crown rebuild in Dilworth typically runs $750 to $1,450. Minor crack repair, where the crown is still structurally sound, runs $350 to $600. The difference comes down to whether the crown can be sealed or has to come off and be replaced. Call (888) 378-0297 and we’ll schedule an inspection to tell you which category your chimney is in.
Is it cheaper to repair or replace a chimney crown?
Repair is cheaper up front at $350 to $600, and it’s the right call when the crown is sound and the cracks are shallow. But if the crown has been patched before and failed again, replacement at $750 to $1,450 is the cheaper option over a handful of years. Repeated patching adds up past the cost of one proper rebuild. Call (888) 378-0297 for an honest assessment.
Do I need a cap and crown together?
Usually yes, if the crown is being rebuilt. Doing both in one visit typically costs $950 to $1,750 combined, which is less than separate jobs priced independently. A cap alone at $285 to $520 is fine when the crown is intact. The inspection tells you which situation you’re in. Call (888) 378-0297 to book one.
Can you come out today for a chimney cap or crown problem?
Same-day service is often possible in Dilworth, and the estimate is free either way. Call (888) 378-0297. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
If your crown has a crack or your cap is missing, the fix is usually less than you’d guess and more urgent than you’d think. Call (888) 378-0297 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. If you’d like the bigger picture on how we work, start at Chimney Sweep Dilworth.
Pricing reflects the Dilworth market as of 2026. Chimney Sweep Dilworth offers free estimates – call (888) 378-0297.
What Our Customers Say
"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Nathan Parker"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."
- Shanice Whitfield"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."
- Tamika Prince