Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Dilworth Homeowners
A missing or loose cap is the single most common way water gets into a chimney in Dilworth, and a hairline crack in the crown is usually right behind it. Neither problem shows up in a routine flue brushing. That’s why we treat the cap and crown as their own job: these are the two components that sit between your masonry and every rainstorm that rolls across the Piedmont.
Our technicians have up to 12 years of experience, and we work from a simple rule. We document what we find before we recommend anything. That means photos and a straight explanation of whether your crown can be coated or needs to come off and be recast. We source components from Gelco and Copperfield, trade-only lines that hold up to the freeze-thaw swings this region gets every winter. Same-day service is available across Dilworth when the schedule allows.
Call (888) 378-0297 to book an inspection or a cap installation. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Cap & Crown Service Includes
Cap Installation
A chimney cap is a vented cover that sits on top of the flue and keeps rain, birds, squirrels and wind-driven debris out of the chimney. You need one if your flue is open to the sky, which is common on older Dilworth homes where the original cap rusted away or was never fitted. We install single-flue and multi-flue caps from Gelco and Copperfield, sized to the actual flue dimensions rather than whatever fits the shelf at a hardware store.

Cap Replacement
Caps fail in predictable ways: rusted mesh, a cracked top plate, legs that have pulled loose from the crown, or a cap that’s simply the wrong size and rattles in the wind. A failed cap stops doing its job long before it falls off, so water and animals get in while the cap still looks intact from the ground. We remove the old unit, check the crown underneath for damage the failing cap may have caused, and set a new cap with proper clearance and fastening.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that sheds water away from the masonry below. When it cracks, water runs into the brickwork, freezes, and slowly pushes the chimney apart from the inside. We repair crowns by cutting out the failed section and rebuilding it to a proper slope, so water runs off instead of pooling. Small cracks get filled and sealed; larger failures get a partial or full recast.

Crown Coating
Crown coating is a flexible, waterproof membrane applied over a sound but weathered crown to stop minor cracking from spreading. It’s the right call when the crown is structurally intact but has surface checking and hairline fissures that let water in. We prep the surface properly first, because a coating over a dirty or damp crown peels within a season. This is a protective step, not a repair, and we’ll tell you plainly when a crown is past coating and needs rebuilding instead.
Multi-Flue Cap
Homes with two or three flues side by side, typically a furnace flue plus a fireplace flue, need a single cap that covers the whole stack rather than individual caps that leave gaps between them. Multi-flue caps are built to the exact footprint of your chimney top, which means measuring the flue spacing and the crown dimensions. We fabricate and fit these so every flue is covered and the whole assembly sheds water as one unit. If your chimney has more than one flue and only partial coverage now, this is usually the fix.
Custom Cap
Oversized chimneys, unusual flue arrangements, and stone or stucco stacks that don’t match standard cap dimensions all call for a custom-built unit. A cap that doesn’t fit correctly lets water in at the edges and can trap moisture against the crown, which is worse than no cap at all. We take measurements on site and have the cap built to match, in copper or stainless depending on what the stack needs. Custom work takes a little longer to schedule, but it’s the only way to cover a non-standard chimney properly.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with Gelco caps and venting components, and we know where those units wear out first: the mesh, the mounting legs, and the seal where the cap meets the crown. Gelco makes a range of standard and multi-flue caps, and matching the right model to your flue size matters more than most homeowners realize. We also fit Copperfield caps and custom tops, which hold up well on stacks that see a lot of sun and freeze-thaw cycling. Our technicians have up to 12 years of experience with these product lines.
For crown work, we use HeatShield ceramic resurfacing where the flue and crown junction needs rebuilding without a full liner replacement, and we install DuraFlex liner systems when a failed crown has let enough water in to damage the flue itself. Whether you have Gelco, Copperfield, HeatShield, DuraFlex, or any other make, we can help. The brand on the cap matters less than whether it’s sized, seated and sealed correctly, and that’s the part we check on every job.
Signs You Need Chimney Cap & Crown Right Now
- Water stains on the ceiling or firebox. Brown rings on the ceiling near the chimney, or dampness inside the firebox after rain, almost always trace back to a failed crown or a missing cap. The masonry soaks up water and it shows up inside the house days later. If you’re seeing this after every storm, it’s worth a look now rather than after a freeze.
- A visible crack in the crown from the ground. Hairline cracks are common and often fixable with coating. Wider cracks, or a crown that’s crumbling at the edges, mean water is already getting into the brickwork. That’s the point where a small repair turns into a masonry job if it’s left through a winter.
- Rusted or missing cap mesh. Once the mesh rusts through, birds, squirrels and bats get into the flue. A nest blocks the flue and creates a real carbon monoxide risk the first time you light a fire. A cap with holes in the mesh is a cap that needs replacing.
- Debris in the firebox after wind. Leaves, twigs or grit showing up in the firebox after a windy day means the cap isn’t seated right or has come loose. It’s a small fix now and a flue obstruction later.
- The cap is crooked or rattling. A cap that’s tilted or moves in the wind has lost its fasteners or was set on a crown that’s failing underneath. Either way it’s not sealing, and it can come off entirely in a strong storm.
Our Chimney Cap & Crown Process – Step by Step
- 1
We start with an inspection. Every cap and crown job begins with a look at the full chimney, not just the top. We check the flue, the firebox and the crown together, because a failed crown is often a symptom of a flue problem below.
- 2
We photograph what we find. You get images of the crown, the cap and any flue damage, so you can see the problem yourself rather than taking our word for it. This is where a lot of sweep-only companies stop short, and it’s the step that keeps recommendations honest.
- 3
We explain the options and the cost. We’ll tell you what can wait and what shouldn’t, and give you a written estimate before any work starts. If a crown can be coated instead of rebuilt, we’ll say so.
- 4
We do the work with professional-grade materials. Crowns get rebuilt to a proper slope, caps get sized and fastened to the actual flue dimensions, and we seal the cap-to-crown joint so water can’t get in at the edge.
- 5
We check the finished job and clean up. We confirm the cap is seated, the crown sheds water, and the flue is clear before we leave. You get a final look at the completed work, and we’ll tell you when the next inspection makes sense.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Dilworth?
A typical chimney cap installation in Dilworth runs $250 to $650 depending on flue count, cap material and whether the crown needs attention underneath. Crown coating is usually the smaller job, around $300 to $550, while a full crown rebuild runs $600 to $1,400 or more if the masonry below has taken on water damage.
Multi-flue and custom caps sit at the higher end of the cap range, since they’re built to the exact footprint of your stack. The factors that move the number most are the number of flues, whether the crown is sound or cracked, and whether we’re working on brick, stone or stucco. A cap that’s correctly sized usually costs less over time than a cheap one that fails in two seasons.
The written estimate sets the final price. We include the inspection, the photos and a clear breakdown of what’s being replaced, so you can see exactly where the money goes. There’s no obligation to book the work the same visit.
Chimney Cap & Crown Near Dilworth – Our Service Area
We cover Dilworth and the surrounding neighborhoods, including Sedgefield, Elizabeth, Myers Park, Eastover and Wesley Heights. Most jobs in these areas can be scheduled within a few days, and same-day service is available when the schedule allows. If you’re just outside these neighborhoods, call and we’ll confirm coverage. You can also read more about our chimney cap & crown work in Sedgefield, or the same service in Elizabeth.
Serving Dilworth, NC – Our Local Coverage Area
We serve Dilworth and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Dilworth
A chimney cap is the vented cover on top of the flue that keeps rain, animals and debris out, while the crown is the concrete or mortar slab at the top of the chimney that sheds water away from the masonry. They work together: the crown protects the brickwork, and the cap protects the flue opening. When either one fails, water gets in and the damage spreads downward. We handle both as a single service. Call (888) 378-0297 for an exact quote – estimates are free.
Most cap installations take a couple of hours, and crown coating is usually a half-day job. A full crown rebuild takes longer, often a full day or more depending on the size of the chimney and whether the masonry needs repair underneath. Custom caps need lead time for fabrication. We’ll give you a realistic timeline with the written estimate.
Cap installation typically runs $250 to $650, crown coating around $300 to $550, and a full crown rebuild $600 to $1,400 or more. The final price depends on flue count, whether the crown is sound, and the material you choose. The written estimate sets the final price, and there’s no charge for the estimate itself. Call (888) 378-0297 for an exact quote – estimates are free.
Yes. We fit and replace Gelco and Copperfield caps, along with HeatShield and DuraFlex products for the flue and crown work beneath them. Our technicians have up to 12 years of experience with these lines. If you have a different make, we can still help; the fit and seal matter more than the label.
Same-day service is available when the schedule allows. We answer 24/7 on the phone. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. We’re closed Saturday.
We stand behind our workmanship and the materials we install. The specific warranty depends on the product line and the type of job, so we’ll spell it out in the written estimate before any work starts. If something isn’t right after the job, call us and we’ll take a look. Call (888) 378-0297 with questions about a specific product.
You don’t need to do much. Clear access to the fireplace and the chimney exterior helps, and let us know if you’ve had water in the firebox or seen debris after storms. If you’ve had previous work done on the cap or crown, mention it so we know what we’re looking at. Beyond that, we handle the rest on site.
Schedule Your Chimney Cap & Crown Service in Dilworth Today
A sound cap and crown are the cheapest insurance your chimney has against water damage, and the fix is usually straightforward once we know what we’re dealing with. Call (888) 378-0297 to book an inspection or a cap installation. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free and there’s no obligation.
Written by the team at Chimney Sweep Dilworth.